How to Melt Silver to Make Jewelry

0

How to melt silver to make jewelry at home is a basic skill that can be used to recycle silver. Sea glass makes a perfect complement to this beautiful craft.

how-to-melt-silver-to-make-jewelry
Pin this post to save this information for later.

Walking along the beach, Allen McGhee isn’t just there for the beautiful ocean view. He’s on the hunt for sea glass and smaller beach stones that might make a nice piece of jewelry or a DIY sea glass art project. Brown and green sea glass are common, red and blue are more elusive, but all have the potential of being transformed into a recycled work of art. Tackling this beautiful craft may be easier than you think, especially with some helpful hints to get you started.

Preparing Cuttlefish Bone Molds

Cuttlefish are cephalopods like octopuses and squid. Cuttlefish bone makes an excellent material for creating molds for jewelry-making endeavors. Cuttlefish bone is inexpensive and readily available from jewelry suppliers and pet stores. However, it’s generally cheaper at pet stores, especially those that buy and sell it in bulk.

Cuttlefish bones have a hard side and a soft side. It’s important to inspect each piece carefully to make sure the soft side of the cuttlefish bone is relatively flat. You don’t want any large cracks or indentations that can’t be easily sanded out. These can detract from your design or cause the cuttlebone to break during the jewelry-making process.

how-to-melt-silverChoose medium-sized pieces that are large enough to cut in half. McGhee likes to use a flush-cut saw to halve his pieces, although you can use a jeweler’s saw or a coping saw.

When cutting a cuttlebone in half, always place the soft side down and cut from the hard side. This helps prevent cracking or splitting. The cutting process will create a lot of dust, so be sure to wear the appropriate eye protection throughout the entire process.

You also want to make sure you’re wearing appropriate clothing since you will be working with an open flame. Clear your work surface so it is free of debris that can catch on fire, such as paper towels or cloth rags.

After the cuttlebone is halved, you must prepare it to be used as a mold. Sand the soft side of the cuttlefish bone to create a smooth contact surface that provides a perfect fit between the two halves. Some people rub the soft sides of the two halves together, but McGhee likes to use sandpaper. Lay the sandpaper on a flat surface and rub the soft side of the cuttlefish bone along the top of the sandpaper, not vice versa.

McGhee uses a circular motion. Rubbing back and forth can create a curved surface you don’t want. Both halves must be flat when finished. While the sandpaper helps create a smooth surface, it doesn’t detract from the natural growth lines found within the bone. These lines resemble wood grain and give each piece a unique texture.

How to Melt Silver to Make Jewelry – Simplified Steps

STEP 1: Cut the cuttlefish bone in half

STEP 2: Sand soft sides of the cuttlebone until smooth

STEP 3: Blow off residual dust

STEP 4: Carve a design into cuttlebone

STEP 5: Bind the two halves together

STEPS 6 & 7: Melt and pour the metal

STEP 8: Remove the hardened metal jewelry piece

how-to-melt-silver-to-make-jewelry
A finished silver piece by Allen McGhee.

How to Melt Silver to Make Jewelry – Carving the Design 

McGhee carves all his designs freestyle by hand. This is probably the most creative part of the process and one he enjoys immensely as an artist. He creates each carving using a variety of wood carving tools and dental tools. Take care when carving your design because it takes very little pressure to etch the surface. You don’t want to go too deep and risk breaking the cuttlebone.

how-to-melt-silver-to-make-jewelry
Inside one cuttlebone design, you can see the notch being cut to hold a piece of sea glass and all the natural grain in the bone. Another one is finished and ready to pour.

Carve your design into one of the halves of the cuttlefish bone and leave the other side unmarred. This is also when McGhee notches a place to insert a piece of sea glass or beach stone into the mold. Sometimes he incorporates more than one piece of glass or stone into the design based on what he envisions.

While he’s carving, he uses a manual air blower to remove dust from the surface of the cuttlefish bone so the lines of his design are crisp. Because he primarily creates pendants, he either includes some type of loop or opening in the design or drills a hole in the top of the finished piece for a chain. Once he’s satisfied with the design, he cuts some air reliefs. These are simply a few thin lines that radiate from the design.

how-to-melt-silver-to-make-jewelry
Another completed carving that will be filled.

“Air reliefs help make sure the melted metal gets all the way to the bottom of the mold,” said McGhee. “Without them, the metal may only fill the crevices of your design partway and it comes out incomplete. Since you can’t reuse the mold, you have to start over, but you can melt the metal again and reuse it.”

Next, sandwich the two halves together with the flat sides facing each other and bind them. McGhee likes to wire the two pieces together. He says you can also use a clamp but wire is easiest. No matter what you use, be sure the pieces are tight to ensure none of the scorching hot, melted metal leaks out the bottom.

Carve out a pouring cone at the top of the cuttlefish. The cone is a large indentation and should just meet the top edge of the design inside. This opening is where you’ll pour your melted metal.

Cuttlefish bone is a popular option for jewelry molds because it’s naturally resistant to the heat of melted metals, but the process does destroy the mold.

QUICK TIP: Don’t throw away your used cuttlebone. A cuttlebone mold isn’t reusable for jewelry-making, but it’s recyclable as plant food.

How to Melt Silver to Make Jewelry – Pouring  

McGhee prefers sterling because of its lower melting point. It’s easier to work with and more desirable than some metals. It’s also much cheaper than gold, making it a great metal when you’re learning. While he’s used bronze some, silver remains his go-to metal. You can buy silver castings, sheets and tubes from various sources, but you can save money and practice recycling by purchasing used silver. McGhee buys broken jewelry, sterling silver flatware and other odd pieces of silver from pawnshops or at garage sales. When he uses old forks, spoons, cups or other large pieces of silver, he must first chop them down to size. The pieces must be able to fit inside your crucible. Plus, smaller pieces of silver melt faster than larger ones.

how-to-melt-silver-to-make-jewelry
Poured with bronze and cooling in mold.

All you need to melt metal is a propane torch, propane, a crucible to hold the metal while it’s melting and some borax to act as flux. McGhee uses the small 16-ounce camp stove replacement propane tanks because they’re easier to manage since they’re small and they’re relatively cheap at about $4 a piece.

When preparing to melt, estimate how much scrap silver you need to fill your mold.

It’s better to overestimate because you can always remelt any unused metal. Place the metal into a ceramic crucible and begin heating it with your torch to melt it. Add a small amount of borax as it heats and starts to melt to prevent it from oxidizing. Carefully swirl the crucible as the metal begins to melt until it’s completely liquified.

how-to-melt-silver-to-make-jewelry
A finished silver piece by Allen McGhee.

Once you have liquid metal, pour it into the pouring cone you created. Be prepared to pour the molten metal into your mold immediately. If it cools, it will harden again. To get a nice pour, you don’t want the metal to cool down even a little as it goes into the mold.

Once the liquid metal reaches the top of the opening, stop pouring. The metal usually hardens quickly but stays very hot to the touch for a while. The safest option is to let it cool inside the mold before opening it up.

McGhee likes to open the mold as soon as the metal has hardened and throw finished pieces into a container of water to cool down quickly. However, if you choose this route, be careful as the metal will be hot enough to cause a serious burn. Wear heat-resistant gloves to protect your hands.

WARNING! Cuttlebone puts off a strong odor once the hot metal is poured inside and singes the surface of the cuttlebone.

This story about how to melt silver to make jewelry previously appeared in Rock & Gem magazine. Click here to subscribe! Story and photos by Moira K. McGhee.

Things You’ll Need

• SILVER SCRAP
• CUTTLEFISH BONE
• CERAMIC CRUCIBLE
• BORAX
• SANDPAPER
• PROPANE TORCH
• PROPANE
• FIRE BRICK OR CONCRETE BOARD
• BINDING WIRE OR CLAMP
• FLUSH CUT SAW
• CARVING TOOLS
• MANUAL AIR BLOWER
• SAFETY GLASS
• HEAT RESISTANT GLOVES

how-to-melt-silver-to-make-jewelry